求翻译不要百度有道翻译的 别百度了 大神速度来翻译下 骗分的别来了 跪求 谢谢谢谢了

1、包装复称的选择
根据客户包装要求的不同，选择相应的包装袋，并根据包装袋容量的大小选择合适量程的电子称
2、复称电子称校准
每班前都要对所使用的复称电子称按电子称校准规范的要求进行校准，同时检查电子称外观、显示等有无异常，保证电子称合格使用
3、设定重量
按包装要求设定包装机在线称相应的定重数值，在线称重由于受各因素影响，所有每个包装的在线重量只是一个参考数值，需经常通过包装后的复称重量对在线重量进行对比调整
4、在线称的校准
操作人员使用包装机在线称前需进行自校操作，小包装称用外力施加一定负荷，无负荷后看是否能归零；大包装机使用前去皮清零，看操作是否正常，每台设备重复3次，看设备显示数值是否稳定。（异常记录）
5、生产过程
生产过程中按在线称的定重数值接装滑石粉
6、生产重量控制
（1）、在接装滑石粉的过程中，生产人员要时刻注意包装机上的在线称的显示数值，达到设定重量数值后，要立刻停止接装滑石粉，并按规定包装方法进行封包接装口
（2）、对于能设定重量自动停机的设备，可定期巡查即可
7、复称
（1）、每班生产的第一包都要复称
（2）、小包装要求每班生产一托盘需随机复称2包，小于一托盘也按抽检2包执行。每班班长抽检数量（由厂长根据生产情况制定）
（3）、大包生产要求每包都需要复称
8、重量调整
（1）、小包复称后重量如与标准重量有差异，要加大抽检数量，对之前生产的包装重量进行复称，同时通过减少包装袋中滑石粉重量的方法达到包装重量的一致性
（2）、大包复称后如发现与标准重量有差异，要通过现场添加或减少包装袋中滑石粉的方法达到重量的一致性
9、定重数值调整
如复称过程中发现包装重量与设定重量差异较大，应对在线称的设定数值进行调整
10、记录
车间按要求做好复称记录，并达到要求复称的数量，并及时上交记录；
注意事项：
1、复称时要保持包装袋干净，减少附着物对包装重量的影响
2、复称时电子称上要保持干净，不能有杂物，影响复称操作
3、复称过程要注意轻拿轻放，不要对电子称造成冲击损坏
4、校准用的砝码要仔细保管，不能损坏影响电子称校准
5、电子称在使用时最好能定置摆放，防止应位置改变地面不平对复称的影响
6、电子称要定期检定和自校，并保留相应记录，以便核对。
7、电子称最好有减震处理，减少震动对复称的影响

1, the packaging said the resumption of choice according to customer requirements of different packaging, select the appropriate bags, and according to the size of bag capacity select the appropriate range of electronic scales
2, said the resumption of said electronic calibration class before going to the used complex said electronic scales electronic scales calibrated according to the specification requirements for calibration, electronic scales also check the appearance, display, etc. without exception, to ensure conformity with
3 electronic scales, packaging requirements set by set weight packaging machine online said corresponding fixed weight value, online due to various factors weighing all online weight of each package is only a reference value, the need to re-often through packaged weighed to compare the online weight adjustment
4, line operator, said calibration using known before packing machine online the need for self-calibration operation, small package, said use force to impose a certain load, no load to see if the energy zero; big clear packaging machine peeled before use, to see whether the operation is normal, repeated three times for each device, see the device displays numerical is stable. (Exception record)
5, the production process of the production process online, said at a fixed weight value tipping talc
6, producing weight control (1), in the process of tipping talc, production personnel should always pay attention to the packaging machine online says The display value reaches the set weight value, immediately stop tipping talcum powder, according to the provisions packing method for packet tipping mouth (2), the weight can be set for automatic shutdown of equipment, regular inspections to
7, complex called (a), the production of first class package must be re-called (2), a small tray packaging requirements needed to produce one random class complex called two bags, less than one pallet also by sampling two package execution. Class squad sampling number (based on production by the director to formulate a) (3), a large bag production requires each package requires complex called
8, weight adjustment (1), said the resumption of weight after parcel if there are differences with the standard weight, to add large number of sampling on the production of packaging weight before multiplexing said, while talc by reducing the weight of the bag way to achieve consistency in packaging weight (2), said the resumption of large package found after differences with the standard weight, through field to add or reduce bag weight of talc way to achieve consistency
9, fixed weight value adjustment process as complex called the packaging weight and set weight differences, the value is set against online said make adjustments 10 records workshop said the resumption of records required to do and to achieve the required number of multiplexing said, and promptly turned over to the record; Note: 1, said the resumption of bags to remain clean and to reduce the impact of attachments on the package weight 2, re-called when Electronics said on should be clean and there is debris, affecting complex called Operation 3, said the resumption of the process should pay attention gently, do not impact on the electronic scale damage 4, the calibration of weights should be carefully kept, not broken affect electronic said calibration 5, electronics when in use it is best to set-placed location should be changed to prevent uneven ground on the complex, said the impact of six, electronic scales to regularly test and self-calibration, and keep appropriate records for verification. 7, electronic scales better to have shock treatment, to reduce the impact of vibration on the complex called

1, packaging complex called selection according to the customer packaging requirements of different choice of packing bag, corresponding, and according to the package size selection of appropriate range, electronic said 2 said the complex electronic calibration to the use of said electronic calibration by electronic calibration specification of each class, at the same time check the electronic appearance, display and other abnormal, ensure the electronic "qualified using 3, setting weight according to the packing requirements set online packaging machine called the corresponding weight value of online weighing, due to various factors, all online weight of each package is only a reference value, often through packaging complex called weight contrast adjustment of online weight 4, online called calibration operator using the online packaging machine that is needed before since the school operation, small package called applied load with external force, whether can return to zero at no load; packaging machine using skin clear, to see whether the operation is normal, each device is repeated 3 times, see equipment to display the numerical stability. (abnormal records) 5, the production process in the production process according to the online said the fixed-weight numerical tipping talcum powder 6, production of weight control (1), in the process of connecting with talcum powder, production personnel should always pay attention to online packaging machine called the display value, reaches the set weight value, should immediately stop tipping the talcum powder, and in accordance with the provisions of packaging method for packet tipping mouth (2), for can set the weight of equipment automatic shutdown, can be regular inspection can be 7, said Fu (1), each class production of the package should also said the complex (2), small packaging requirements of each class a tray for production random complex called 2 pack, less than a tray by sampling 2 package execution. Each class monitor the number of sampling (formulated by the Director under production) (3), big production requirements of each package to say 8, weight adjustment (1), small complex called weight as with standard weight differences, to increase the number of sampling, packaging weight prior to production are complex, at the same time through consistent method of reducing packaging bag talcum powder weight to package weight (2), large complex after saying if there are differences and standard weight, through adding or reducing method of talcum powder in the packaging bag to achieve consistency weight 9, weight value adjustment such as complex called found in the process of packaging weight and set weight large differences in site, set the value to 10, the adjusted online said the record shop according to the requirements of good complex called records, and meet the requirements of complex called the number, and make a record; note: 1, keep packing bag clean to say, reduce the effect of attachment on packaging weight 2, said Fu. Electronic scale to keep clean, no debris, influence of complex operation called 3, said the complex process should pay attention light-light, don't call the impact damage 4, calibration weights to keep electronic, can not damage Effect of electronic calibration 5, electronic said when in use, best can set display, prevent the position should be changed uneven ground effects on complex called 6, electronic said to regularly test and self-correcting, and keep the relevant records, in order to check. 7, electronic said the best damping treatment, reducing vibration effects on complex called

经翻译，译文如下：
The selection of, packaging after said
Depending on the customer's packaging requirements, choose the corresponding packing bags, and according to the size of the packing bag capacity choose appropriate range of electronic said
2, after called electronic calibration
Before each class will be used by the compound called electronic calibration according to the requirement of the electronic scale calibration specification, at the same time check whether there is any abnormal on electronic said appearance, display, etc, ensure qualified using electronic scale
3, set the weight
According to the packaging requirements set packing machine online called corresponding weight value of online weighing due to the effect of various factors, all each package online weight is just a reference value, need often after packaging by a compound called comparing weight for online weight adjustment
4, according to online calibration
Operators use online need to self correcting operation before said packaging machine, small package with external forces exerted a certain load, look to whether can after no-load zero; Bag installed to use leather, see whether normal operation, each device repeat 3 times, see if equipment display numerical stability. (abnormal records)
5, the production process
Production process according to the online called heavy numerical answer the talcum powder
6, production control weight
(1), in the process of meet with talcum powder, production personnel are aware of the packing machine online called display value, after reaching set weight value, should stop immediately after talcum powder, and packaging method according to the rules in the packet by mouth
(2), the weight to set the automatic stop device, can be regular inspections
7, after said
(1), each shift production after the first a pack of all want to say
(2) a tray should be random, small packaging requirements per shift production after said 2 package, less than a pallet also according to the sampling 2 package. Each class monitor sampling quantity (set by the factory director according to production situation)
(3), bag production requirements each package needs to be said
8, weight adjustment
(1), packet said if any difference with the standard weight, the weight to increase sampling quantity, and weight to the packing of the production before to say, at the same time by reducing the packing bag of talcum powder weight method to achieve consistency of packaging weight
(2), such as after bag after said, found that has difference with standard weight, through the scene to add or reduce talcum powder in packaging method to achieve the consistency of weight
9, heavy value adjustment
Such as after said found in the process of packaging weight and setting weight difference is bigger, adjusted online according to set value
10, records
Workshop after said records as required, and meet the requirements according to the number of, and timely submit the record;
Note:
1, after said to keep the bags clean, reduce the attachment of packaging weight
2, after said electronic scale to keep clean, cannot have sundry, impact according to operation
3, after said process must pay attention to the light to take light put, do not say to electronic impact damage
4, the calibration weights shall be carefully kept, shall not damage effects on electronic calibration
5, when use electronic scale best can put home, prevent should position the ground uneven effects on complex said
6, electronic said to regularly check and self-calibration, and keep relevant records, so as to check it.
7, electronic said had better shock absorption treatment, reducing vibration effects on complex said
欢迎追问！